Parameters
Flow: 18-122m3/h
Head scope: 5-32m
Power: 15.5-110kw
Pump outlet diameter: 40mm-250mm
Temperature: generally≤80℃ especially up to 110℃
Drive form: electric motor
Product Applications
The MSP vertical slurry pump is designed mainly for conveying corrosive, coarse particles and high concentration slag slurry.
Widely used in metallurgy, mines, coal, electricity, building materials, environmental protection and other industrial applications.
Type | Outlet Dia. | Bearing Frame | Max Power | Max. Particle Size | Pumping Depth | No. of Vanes | Impeller Dia. |
mm | Kw | mm | mm | mm | |||
40 | P | 15 | 12 | 900*1200 | 5 | 188 | |
65 | Q | 30 | 15 | 900*1200*1500 | 5 | 280 | |
100 | R | 75 | 32 | 1200*1500*2100 | 5 | 370 | |
150 | S | 110 | 45 | 1500*1800*2100 | 5 | 450 |
Type | Outlet Dia. | Bearing Frame | Max Power | Max. Particle Size | Pumping Depth | No. of Vanes | Impeller Dia. |
mm | Kw | mm | mm | mm | |||
40 | P | 15 | 12 | 900*1200 | 5 | 188-195 | |
65 | Q | 30 | 15 | 900*1200*1500 | 5 | 280-290 | |
100 | R | 75 | 40 | 1200*1500*2100 | 5 | 370 | |
150 | S | 110 | 45 | 1500*1800*2100 | 5 | 450 |
Pump compositions
The SP pump is a vertical centrifugal slurry pump with a vertical downward pump inlet, while the outlet is at the top. The pump is composed of a lower strainer, pump bogy, impeller, shaft, guard plate, and support structure. The upper part of the pump is where the bearing is located while the pump is installed in the liquid. Therefore, there is no need for a shaft seal.
Part Description | Material Specification | Material Options |
Shaft | 4140 Mild Steel | Available on Request |
Bearing Housing | Cast Iron | |
Column | Mild Steel | |
Upper Strainer | Rubber | Cast Iron |
Lower Strainer | Cast Iron | |
Back Liner | 27% Chrome White Iron | |
Pump Casing | 27% Chrome White Iron | Rubber Lined White Iron |
Impeller | 27% Chrome White Iron | Rubber |
Discharge Pipe | Mild Steel | Rubber Lined Mild Steel/ Composite |
Adaptor Plate | Mild Steel | |
Bolts | Zinc Plated Steel |
Structural Advantages
1. The pump adopts 27% Cr high chromium or rubber impeller.
2. The over flow component is composed of materials like, 27% Cr high chromium or lining rubber cast iron.
3. There are no shaft seal requirements.
4. There is a filter under the rubber lining of the cast iron to reduce clogging.
5. The greatest length of a submerged part is 2100mm, which is easy to work with.
6. The "L" modification series of extended shafts and column bearings can be used for deep groove applications that are unsuitable with a cantilever design.
7. The simple structure design makes it easy to replace over flow parts.
Material selections
According to the transported medium to choose high chromium or rubber material.
Product features
1. Wearing parts possess a long service life; The overflow particle size is large; It's convenient for pump maintenence;
2. Low operating cost and high reliability;
3. The structure is simple, and the device is convenient;
4. There is no need for any shaft seal and shaft seal water, under the condition of insufficient suction the pump can also work normally.